Example contents of config.txt file

For file config.txt
TRANSFER SETTINGS TO EMAILER UNIT:
These settings will be written to emailer unit
if this file config.txt exists on the USB Drive.
Edit these settings and save to config.txt
Enclose values within brackets: ()


************* Email Distribution *************
email1:.......................>(rocky@printrecorder.com)
email2:.......................>(peter@premiumglass.com)
email3:.......................>(jrfox@ap-windows.com)
email4:.......................>()
email5:.......................>()
email6:.......................>()
email7:.......................>()
email8:.......................>()

*********** Email Subject Line ***************
Maximum length: 60 characters:
>(Email from Model RJ )


************* Email Body *********************
Amount of most recent lines logged:
Choose 1 to 1,000.............>(9)

Double Linefeeds..............>(Yes)
E.g. (Yes) or (No)

************* Email Triggers ******************
1. Send Email after reception of data has
paused. A pause signifies the end of the print report.
Set value of the pause period. Common value = 5
Choose 1 to 60 seconds........>(5)

2. Send Email at a specific time of day.
Useable only if network time, NTP Server,
is available.
Time Format: hh:mm ............>()
Example: (18:45)
Use empty brackets ()to disable.

3. Send Email only if keyword is detected in print data:
keyword is: ...................>()
Examples: Station B, batch 5
All other emails are disabled.
Empty brackets means: Don't detect keyword.

4. Enable Model RJ to check an email account
for an email trigger command.
Enable email check: Yes or No ....>(No)

5. Disable all email transmissions but
continue logging all data to USB Drive.
Disable all emails: Yes or No ....>(No)


********* Optional Email Attachment **********
Attachment may not workwith some email clients.
Attach: log.txt ..............>(No)
Example: (Yes) or (No)

********** Serial Interface Baud Rate ********
Choices: 1200, 2400, 4800, 9600, 19200,
38400, 57600, 115200
Baud:.........................>(9600)
Data Bits: 7 or 8.............>(8)
Parity: Odd, Even, None.......>(None)


************* Send Email Setup ********************
SMTP Server...................>(smtp.gmail.com)
Port E.g. 587 or 465.........>(587)
TLS Mode......................>(Yes)
Sender email address..........>(martian@gmail.com)
Password......................>(sr66$Qytz)


************* Receive Email Setup ********************
The RJ Unit will check this email server for email that
contains user command characters: &&& command
POP Server...................>(pop.gmail.com)
Ports:110 basic common
143 IMAP
993 IMAPS SSL
995 SSL/TLS Encrypted
POP Port.....................>(995)
POP Username-ID..............>(martian@gmail.com)
POP Password.................>(sr66$Qytz)
POP Use SSL..................>(Yes)
POP Download and erase.......>(Yes)
To command the Model RJ to send its USB log file, the user
may send an email to Model RJ POP Username-ID
email address above. The email must include the &&&
3 ampersands) text anywhere in the email,
e.g. Subject or Body.

To transfer the above settings to the Model RJ emailer
unit save this config.txt file to a USB Drive. Install
the USB Drive onto Model RJ emailer unit. The emailer
unit will adopt the settings into its own flash memory.
Delete config.txt after Model RJ emailer unit has
been configured.

To transfer the emailer unit configuration settings
back to a USB Drive for editing press the emailer
unit pushbutton: TRANSFER CONFIGURATION TO USB DRIVE.

Install config.txt on the USB drive only when you
wish to write configuration settings to the emailer
unit.
Rev. 3.7